Steps
Module: xfea.problem.steps
Analysis steps: static, dynamic and heat transfer steps, perturbations (modal, buckling), and contact controls.
ContactControls
Section titled “ContactControls”ContactControls(
step_growth_threshold: int = 20,
max_divergences: int = 25,
target_iterations: int = 9,
soft_cutback_limit: int = 40,
step_growth_bound: int = 16,
fast_growth_trigger: int = 6,
cutback_factor: int = 5,
residual_tolerance: float = 0.02,
correction_tolerance: float = 0.05,
zero_load_tolerance: float = 0.1,
stabilize: bool | float | None = None,
)
The solver’s convergence settings for a step with contact, written as its *CONTROLS.
Pass them as a step’s contact_controls. They apply only when the model
has a contact interface; a step with contact and none given gets
ContactControls(). Each setting fills one position of the solver’s
*CONTROLS lines (see Notes); some names are older than that mapping
and say less than the position does.
Parameters
| Name | Type | Description |
|---|---|---|
| step_growth_threshold | int, optional | I0 (default 20): the iteration after which an increment whose residual grows twice running is cut back. |
| max_divergences | int, optional | IR (default 25): the iteration from which the solver checks the convergence rate and cuts back a slow increment. |
| target_iterations | int, optional | IP (default 9): the iteration after which the looser residual criterion Rp replaces Rn. |
| soft_cutback_limit | int, optional | IC (default 40): the most iterations an increment may take. |
| step_growth_bound | int, optional | IL (default 16): above this many iterations, the next increment is made smaller. |
| fast_growth_trigger | int, optional | IG (default 6): at most this many iterations in two increments running, and the next is made larger. |
| cutback_factor | int, optional | IA (default 5): the most cutbacks one increment may have (a count, not a factor). |
| residual_tolerance | float, optional | Rn (default 0.02): converged when the largest residual force is below this fraction of the average force. |
| correction_tolerance | float, optional | Cn (default 0.05): converged when the largest displacement correction is below this fraction of the increment’s largest displacement. |
| zero_load_tolerance | float, optional | epsilon (default 0.10): forces below this fraction of the average force count as zero. |
| stabilize | bool or float, optional | Contact stabilisation, for solvers that have it: not written by the solver plugin. |
Properties
field_displacement_linestrread-only
The data line of *CONTROLS, PARAMETERS=FIELD, FIELD=DISPLACEMENT: Rn, Cn, (blank), (blank), (blank), epsilon.
time_incrementation_linestrread-only
The data line of *CONTROLS, PARAMETERS=TIME INCREMENTATION: I0, IR, IP, IC, IL, IG, (IS blank), IA.
StaticStep
Section titled “StaticStep”StaticStep(
max_increments=100,
initial_inc_size=1.0,
min_inc_size=1e-05,
max_inc_size=1,
time=1,
nlgeom=False,
modify=True,
contact_controls=None,
**kwargs,
)
A static step: loads applied slowly enough that inertia plays no part, solved for equilibrium.
Linear unless the model makes it nonlinear (contact, one-sided springs,
plasticity) or nlgeom is set; a nonlinear step is solved in
increments of step time, the solver cutting them back when one does not
converge. Add it with add_step(), then its loads.
Parameters
| Name | Type | Description |
|---|---|---|
| max_increments | int, optional | The most increments the solver may take (default 100); the step fails if it needs more. |
| initial_inc_size | float, optional | The first increment, in step time (default 1.0): the whole load at once. |
| min_inc_size | float, optional | The smallest increment, in step time (default 1e-5); the step fails if the solver must cut below it. |
| max_inc_size | float, optional | The largest increment, in step time (default 1). |
| time | float, optional | The step’s length in step time (default 1), a load factor here, not seconds. |
| nlgeom | bool, optional | If True, solve with geometric nonlinearity (large displacements and rotations). |
| modify | bool, optional | Whether this step’s loads replace (True, default) or add to those of the step before; kept, not used by the solver plugin. |
| contact_controls | ContactControls, optional |
The solver’s convergence settings for a step with contact: None uses the defaults. |
| name | str, optional | The step’s name, unique in its problem; one is generated if not given. |
Guidance (steps)
- With contact, a small model converges fastest in one increment (the default). A large one (tens
of thousands of elements) can converge faster from
initial_inc_size=0.1. - Cutbacks repeating at the same increment point to a physical issue (a mechanism, a missing
support), not a numerical one. Unsupported bodies need
ContactControls(max_divergences=...)above 10.
Properties
amplitudesread-only
The amplitudes of the step’s loads, a set, or None if it has no fields.
combinationread-only
The step’s load combination, or None (see add_combination()).
combined_fieldsdict | Noneread-only
The effective fields summed by kind: {field type: one ForceField}; raises ValueError if there are none.
contact_controlsContactControls | Noneread-only
The step’s convergence settings for contact, or None for the defaults (ContactControls()).
The solver plugin writes them as *CONTROLS only when the model has
a contact interface; without contact they have no effect.
displacementsread-only
The step’s imposed displacement fields, a list, or None if it has no fields.
effective_fieldsLoadsFieldGroup | Noneread-only
The fields the solver gets: the step’s fields, factored by its load combination if it has one: None if none.
field_outputsread-only
The field results asked for in this step, a set.
fieldsread-only
The step’s load, displacement and temperature fields, a LoadsFieldGroup, or None.
history_outputsread-only
The history results asked for in this step, a set.
initial_inc_sizeread-only
The first increment, in step time.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
load_casesset[str] | Noneread-only
The names of the load cases the step’s fields belong to, or None if it has no fields.
loadsread-only
The step’s force and gravity fields, a list, or None if it has no fields.
max_inc_sizeread-only
The largest increment, in step time.
max_incrementsread-only
The most increments the solver may take.
min_inc_sizeread-only
The smallest increment, in step time.
modelModel | Noneread-only
The model of the step’s problem.
modifyread-only
Whether this step’s loads replace those of the step before (kept, not used by the solver plugin).
namestr
The object’s name.
nlgeomread-only
Whether the step is solved with geometric nonlinearity.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
restart
Every how many increments restart data is written: False for none.
timeread-only
The step’s length, in step time.
uidUUID | Noneread-only
The object’s unique id, a UUID.
StaticRiksStep
Section titled “StaticRiksStep”StaticRiksStep(
max_increments=100,
initial_inc_size=1,
min_inc_size=1e-05,
time=1,
nlgeom=False,
modify=True,
**kwargs,
)
A static step solved by the Riks (arc-length) method, to follow a load path past a peak load.
Parameters
| Name | Type | Description |
|---|---|---|
| max_increments, initial_inc_size, min_inc_size, time, nlgeom, modify | As for StaticStep. |
Properties
amplitudesread-only
The amplitudes of the step’s loads, a set, or None if it has no fields.
combinationread-only
The step’s load combination, or None (see add_combination()).
combined_fieldsdict | Noneread-only
The effective fields summed by kind: {field type: one ForceField}; raises ValueError if there are none.
contact_controlsContactControls | Noneread-only
The step’s convergence settings for contact, or None for the defaults (ContactControls()).
The solver plugin writes them as *CONTROLS only when the model has
a contact interface; without contact they have no effect.
displacementsread-only
The step’s imposed displacement fields, a list, or None if it has no fields.
effective_fieldsLoadsFieldGroup | Noneread-only
The fields the solver gets: the step’s fields, factored by its load combination if it has one: None if none.
field_outputsread-only
The field results asked for in this step, a set.
fieldsread-only
The step’s load, displacement and temperature fields, a LoadsFieldGroup, or None.
history_outputsread-only
The history results asked for in this step, a set.
initial_inc_sizeread-only
The first increment, in step time.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
load_casesset[str] | Noneread-only
The names of the load cases the step’s fields belong to, or None if it has no fields.
loadsread-only
The step’s force and gravity fields, a list, or None if it has no fields.
max_inc_sizeread-only
The largest increment, in step time.
max_incrementsread-only
The most increments the solver may take.
min_inc_sizeread-only
The smallest increment, in step time.
modelModel | Noneread-only
The model of the step’s problem.
modifyread-only
Whether this step’s loads replace those of the step before (kept, not used by the solver plugin).
namestr
The object’s name.
nlgeomread-only
Whether the step is solved with geometric nonlinearity.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
restart
Every how many increments restart data is written: False for none.
timeread-only
The step’s length, in step time.
uidUUID | Noneread-only
The object’s unique id, a UUID.
DynamicStep
Section titled “DynamicStep”DynamicStep(**kwargs)
A dynamic step: loads that vary in time, with the model’s inertia; time is real time.
Takes the settings of GeneralStep, all as
keywords (max_increments, initial_inc_size, min_inc_size,
max_inc_size, time, …), none of them with a default here.
Properties
amplitudesread-only
The amplitudes of the step’s loads, a set, or None if it has no fields.
combinationread-only
The step’s load combination, or None (see add_combination()).
combined_fieldsdict | Noneread-only
The effective fields summed by kind: {field type: one ForceField}; raises ValueError if there are none.
contact_controlsContactControls | Noneread-only
The step’s convergence settings for contact, or None for the defaults (ContactControls()).
The solver plugin writes them as *CONTROLS only when the model has
a contact interface; without contact they have no effect.
displacementsread-only
The step’s imposed displacement fields, a list, or None if it has no fields.
effective_fieldsLoadsFieldGroup | Noneread-only
The fields the solver gets: the step’s fields, factored by its load combination if it has one: None if none.
field_outputsread-only
The field results asked for in this step, a set.
fieldsread-only
The step’s load, displacement and temperature fields, a LoadsFieldGroup, or None.
history_outputsread-only
The history results asked for in this step, a set.
initial_inc_sizeread-only
The first increment, in step time.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
load_casesset[str] | Noneread-only
The names of the load cases the step’s fields belong to, or None if it has no fields.
loadsread-only
The step’s force and gravity fields, a list, or None if it has no fields.
max_inc_sizeread-only
The largest increment, in step time.
max_incrementsread-only
The most increments the solver may take.
min_inc_sizeread-only
The smallest increment, in step time.
modelModel | Noneread-only
The model of the step’s problem.
modifyread-only
Whether this step’s loads replace those of the step before (kept, not used by the solver plugin).
namestr
The object’s name.
nlgeomread-only
Whether the step is solved with geometric nonlinearity.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
restart
Every how many increments restart data is written: False for none.
timeread-only
The step’s length, in step time.
uidUUID | Noneread-only
The object’s unique id, a UUID.
QuasiStaticStep
Section titled “QuasiStaticStep”QuasiStaticStep(**kwargs)
A quasi-static step: loads applied slowly, inertia neglected; the solver plugin writes it as a static step.
Takes the settings of GeneralStep, all as keywords.
Properties
amplitudesread-only
The amplitudes of the step’s loads, a set, or None if it has no fields.
combinationread-only
The step’s load combination, or None (see add_combination()).
combined_fieldsdict | Noneread-only
The effective fields summed by kind: {field type: one ForceField}; raises ValueError if there are none.
contact_controlsContactControls | Noneread-only
The step’s convergence settings for contact, or None for the defaults (ContactControls()).
The solver plugin writes them as *CONTROLS only when the model has
a contact interface; without contact they have no effect.
displacementsread-only
The step’s imposed displacement fields, a list, or None if it has no fields.
effective_fieldsLoadsFieldGroup | Noneread-only
The fields the solver gets: the step’s fields, factored by its load combination if it has one: None if none.
field_outputsread-only
The field results asked for in this step, a set.
fieldsread-only
The step’s load, displacement and temperature fields, a LoadsFieldGroup, or None.
history_outputsread-only
The history results asked for in this step, a set.
initial_inc_sizeread-only
The first increment, in step time.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
load_casesset[str] | Noneread-only
The names of the load cases the step’s fields belong to, or None if it has no fields.
loadsread-only
The step’s force and gravity fields, a list, or None if it has no fields.
max_inc_sizeread-only
The largest increment, in step time.
max_incrementsread-only
The most increments the solver may take.
min_inc_sizeread-only
The smallest increment, in step time.
modelModel | Noneread-only
The model of the step’s problem.
modifyread-only
Whether this step’s loads replace those of the step before (kept, not used by the solver plugin).
namestr
The object’s name.
nlgeomread-only
Whether the step is solved with geometric nonlinearity.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
restart
Every how many increments restart data is written: False for none.
timeread-only
The step’s length, in step time.
uidUUID | Noneread-only
The object’s unique id, a UUID.
DirectCyclicStep
Section titled “DirectCyclicStep”DirectCyclicStep(**kwargs)
A direct cyclic step: the stabilised response of a structure under a repeated load cycle.
Takes the settings of GeneralStep, all as keywords.
Properties
amplitudesread-only
The amplitudes of the step’s loads, a set, or None if it has no fields.
combinationread-only
The step’s load combination, or None (see add_combination()).
combined_fieldsdict | Noneread-only
The effective fields summed by kind: {field type: one ForceField}; raises ValueError if there are none.
contact_controlsContactControls | Noneread-only
The step’s convergence settings for contact, or None for the defaults (ContactControls()).
The solver plugin writes them as *CONTROLS only when the model has
a contact interface; without contact they have no effect.
displacementsread-only
The step’s imposed displacement fields, a list, or None if it has no fields.
effective_fieldsLoadsFieldGroup | Noneread-only
The fields the solver gets: the step’s fields, factored by its load combination if it has one: None if none.
field_outputsread-only
The field results asked for in this step, a set.
fieldsread-only
The step’s load, displacement and temperature fields, a LoadsFieldGroup, or None.
history_outputsread-only
The history results asked for in this step, a set.
initial_inc_sizeread-only
The first increment, in step time.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
load_casesset[str] | Noneread-only
The names of the load cases the step’s fields belong to, or None if it has no fields.
loadsread-only
The step’s force and gravity fields, a list, or None if it has no fields.
max_inc_sizeread-only
The largest increment, in step time.
max_incrementsread-only
The most increments the solver may take.
min_inc_sizeread-only
The smallest increment, in step time.
modelModel | Noneread-only
The model of the step’s problem.
modifyread-only
Whether this step’s loads replace those of the step before (kept, not used by the solver plugin).
namestr
The object’s name.
nlgeomread-only
Whether the step is solved with geometric nonlinearity.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
restart
Every how many increments restart data is written: False for none.
timeread-only
The step’s length, in step time.
uidUUID | Noneread-only
The object’s unique id, a UUID.
HeatTransferStep
Section titled “HeatTransferStep”HeatTransferStep(
max_increments=100,
initial_inc_size=1,
min_inc_size=1e-05,
max_inc_size=1,
time=1,
max_temp_delta=10,
max_emiss_change=0.1,
nlgeom=False,
modify=True,
restart=False,
steady_state=False,
**kwargs,
)
A heat transfer step: temperatures in the model from prescribed temperatures and exchanges, transient or steady.
Transient by default: time is real time (s in the usual units), and the solver chooses
increments so the temperature changes by at most max_temp_delta in
one. Only temperature fields can be added to it; convection and
radiation come from the model’s boundary interfaces.
Parameters
| Name | Type | Description |
|---|---|---|
| max_increments | int, optional | The most increments the solver may take (default 100). |
| initial_inc_size | float, optional | The first increment, in the step’s time unit (default 1). |
| min_inc_size | float, optional | The smallest increment (default 1e-5); the step fails if the solver must cut below it. |
| max_inc_size | float, optional | The largest increment (default 1). |
| time | float, optional | The step’s length, in the model’s time unit (default 1). |
| max_temp_delta | float, optional | The largest temperature change allowed in one increment (default 10). |
| max_emiss_change | float, optional | The largest emissivity change allowed in one increment (default 0.1); kept, not used by the solver plugin. |
| nlgeom | bool, optional | Kept for the step’s interface; it has no meaning in heat transfer. |
| modify | bool, optional | Whether this step’s temperatures replace (True, default) those of the step before; kept, not used by the solver plugin. |
| restart | int or bool, optional | Write restart data every this many increments: False (default) writes none. |
| steady_state | bool, optional | If True, solve for the steady state: time is then only a load factor. |
Properties
amplitudesread-only
The amplitudes of the step’s loads, a set, or None if it has no fields.
combinationread-only
The step’s load combination, or None (see add_combination()).
combined_fieldsdict | Noneread-only
The effective fields summed by kind: {field type: one ForceField}; raises ValueError if there are none.
contact_controlsContactControls | Noneread-only
The step’s convergence settings for contact, or None for the defaults (ContactControls()).
The solver plugin writes them as *CONTROLS only when the model has
a contact interface; without contact they have no effect.
displacementsread-only
The step’s imposed displacement fields, a list, or None if it has no fields.
effective_fieldsLoadsFieldGroup | Noneread-only
The fields the solver gets: the step’s fields, factored by its load combination if it has one: None if none.
field_outputsread-only
The field results asked for in this step, a set.
fieldsread-only
The step’s load, displacement and temperature fields, a LoadsFieldGroup, or None.
history_outputsread-only
The history results asked for in this step, a set.
initial_inc_sizeread-only
The first increment, in step time.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
load_casesset[str] | Noneread-only
The names of the load cases the step’s fields belong to, or None if it has no fields.
loadsread-only
The step’s force and gravity fields, a list, or None if it has no fields.
max_emiss_changeread-only
The largest emissivity change allowed in one increment.
max_inc_sizeread-only
The largest increment, in step time.
max_incrementsread-only
The most increments the solver may take.
max_temp_deltaread-only
The largest temperature change allowed in one increment.
min_inc_sizeread-only
The smallest increment, in step time.
modelModel | Noneread-only
The model of the step’s problem.
modifyread-only
Whether this step’s loads replace those of the step before (kept, not used by the solver plugin).
namestr
The object’s name.
nlgeomread-only
Whether the step is solved with geometric nonlinearity.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
restart
Every how many increments restart data is written: False for none.
timeread-only
The step’s length, in step time.
uidUUID | Noneread-only
The object’s unique id, a UUID.
Methods
add_field(field)
Add a temperature field (TemperatureField); other fields raise ValueError.
add_load_field(field)
Alias for add_field() to keep compatibility.
ModalAnalysis
Section titled “ModalAnalysis”ModalAnalysis(modes=1, **kwargs)
The structure’s natural frequencies and mode shapes, in the state the step before it left (unloaded if none).
The masses come from the material densities: set them in the model’s units (t/mm3 for N and mm), or the frequencies are wrong.
Parameters
| Name | Type | Description |
|---|---|---|
| modes | int, optional | The number of modes to compute, lowest first (default 1). |
Guidance (analyses)
- After the solve,
modal.frequencieslists the frequencies andmodal.mode_shape(n)gives mode n’s shape.
Properties
field_outputsread-only
The field results asked for in this step, a set.
frequenciesread-only
The natural frequencies, modes 1 to modes in order, as a generator (Hz with time in seconds).
history_outputsread-only
The history results asked for in this step, a set.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
modelModel | Noneread-only
The model of the step’s problem.
namestr
The object’s name.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
rdbread-only
The results database of the step’s problem (see rdb).
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
resultsread-only
Each mode’s result, modes 1 to modes in order, as a generator.
shapesread-only
Each mode’s shape, modes 1 to modes in order, as a generator (see mode_shape()).
uidUUID | Noneread-only
The object’s unique id, a UUID.
Methods
available_modes()
The modes the results hold, a sorted list of mode numbers (empty before the solve).
mode_frequency(mode)
Mode mode’s natural frequency (counted from 1), in Hz with time in seconds.
mode_result(mode)
Mode mode’s result (counted from 1): eigenvalue, frequency, shape, participation factors and effective mass.
Parameters
| Name | Type | Description |
|---|---|---|
| mode | int | The mode, from 1. |
Returns
| Name | Type | Description |
|---|---|---|
class:xfea.results.ModalResult |
The mode’s result. |
ComplexEigenValue
Section titled “ComplexEigenValue”ComplexEigenValue(**kwargs)
A complex frequency step: natural frequencies with damping or gyroscopic effects.
Properties
field_outputsread-only
The field results asked for in this step, a set.
history_outputsread-only
The history results asked for in this step, a set.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
modelModel | Noneread-only
The model of the step’s problem.
namestr
The object’s name.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
rdbread-only
The results database of the step’s problem (see rdb).
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
uidUUID | Noneread-only
The object’s unique id, a UUID.
BucklingAnalysis
Section titled “BucklingAnalysis”BucklingAnalysis(modes, vectors=None, iterations=30, algorithm=None, **kwargs)
Linear buckling: the factors by which the loads of the steps before it must be multiplied for the structure to buckle.
Add it after a static step that applies a reference load; after the
solve, mode_factor(1) times that load is the lowest buckling load.
Parameters
| Name | Type | Description |
|---|---|---|
| modes | int | The number of buckling modes to compute, lowest factor first. |
| vectors | int, optional | The number of trial vectors the eigensolver uses: None takes twice modes (three times above 9 modes). |
| iterations | int, optional | The most eigensolver iterations (default 30). |
| algorithm | str, optional | The eigensolver, "SUBSPACE" or "Lanczos", or None for the solver plugin’s default. |
Properties
field_outputsread-only
The field results asked for in this step, a set.
history_outputsread-only
The history results asked for in this step, a set.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
modelModel | Noneread-only
The model of the step’s problem.
namestr
The object’s name.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
rdbread-only
The results database of the step’s problem (see rdb).
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
resultsread-only
Each mode’s result, modes 1 to modes in order, as a generator.
shapesread-only
Each mode’s shape, modes 1 to modes in order, as a generator (see mode_shape()).
uidUUID | Noneread-only
The object’s unique id, a UUID.
Methods
Lanczos(modes)
A buckling analysis of modes modes with the Lanczos eigensolver.
Subspace(modes, iterations, vectors=None)
A buckling analysis of modes modes with the subspace eigensolver, at most iterations iterations.
available_modes()
The modes the results hold, a sorted list of mode numbers (empty before the solve).
mode_factor(mode)
Mode mode’s buckling factor (counted from 1): the multiple of the load at which it buckles.
mode_result(mode)
Mode mode’s result (counted from 1): its buckling factor and shape.
Parameters
| Name | Type | Description |
|---|---|---|
| mode | int | The mode, from 1. |
Returns
| Name | Type | Description |
|---|---|---|
class:xfea.results.BucklingResult |
The mode’s result. |
LinearStaticPerturbation
Section titled “LinearStaticPerturbation”LinearStaticPerturbation(**kwargs)
A linear static response to a small load about the state the step before it left, not carried over.
Properties
field_outputsread-only
The field results asked for in this step, a set.
history_outputsread-only
The history results asked for in this step, a set.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
modelModel | Noneread-only
The model of the step’s problem.
namestr
The object’s name.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
rdbread-only
The results database of the step’s problem (see rdb).
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
uidUUID | Noneread-only
The object’s unique id, a UUID.
SteadyStateDynamic
Section titled “SteadyStateDynamic”SteadyStateDynamic(**kwargs)
A steady-state response to harmonic loading over a range of frequencies.
Properties
field_outputsread-only
The field results asked for in this step, a set.
history_outputsread-only
The history results asked for in this step, a set.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
modelModel | Noneread-only
The model of the step’s problem.
namestr
The object’s name.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
rdbread-only
The results database of the step’s problem (see rdb).
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
uidUUID | Noneread-only
The object’s unique id, a UUID.
SubstructureGeneration
Section titled “SubstructureGeneration”SubstructureGeneration(**kwargs)
The generation of a substructure (superelement) from part of the model.
Properties
field_outputsread-only
The field results asked for in this step, a set.
history_outputsread-only
The history results asked for in this step, a set.
keyAny | Noneread-only
The object’s key (its number) in what it is registered to; None until it is given one.
modelModel | Noneread-only
The model of the step’s problem.
namestr
The object’s name.
problemProblemread-only
The problem the step is in; raises AttributeError if it is in none.
rdbread-only
The results database of the step’s problem (see rdb).
registrationAny | None
The object this one is registered to (a part, a model, a step, …), or None.
uidUUID | Noneread-only
The object’s unique id, a UUID.
© 2026 Francesco Ranaudo · Text and pictures CC BY 4.0 · Code Elastic License 2.0 · how to reuse them